REC

Complete Checklist for Pre-Paint Exterior Pressure Washing

If you're planning to repaint the outside of your Darwin home in 2026, the quality of your finish depends largely on what happens before the first brush or roller touches the wall. Pressure washing is one of the most important preparation steps, yet it's also one of the easiest to get wrong. Too much pressure can damage surfaces, while too little leaves behind the grime, mould and chalk that cause paint to peel. This checklist walks you through the entire process, with a focus on the unique conditions we face in the Top End.

Why Pre-Paint Pressure Washing Matters in Darwin

Darwin's tropical climate is tough on exterior paint. High humidity, intense UV, heavy Wet Season rain and salt-laden air in coastal suburbs such as Nightcliff, Fannie Bay, Casuarina and Lee Point all contribute to surface contamination. Mould, mildew and algae can establish quickly on walls, eaves, fences and concrete, and they will continue to grow beneath new paint if they aren't properly removed.

Paint also struggles to bond with chalky, dusty or greasy surfaces. Over time, older paint breaks down and leaves a powdery residue that acts like a barrier between the old coating and the new one. A thorough wash removes this layer and gives your new paint a clean, stable surface to grip.

Step One: Inspect the Property Before You Start

Before you pick up a pressure washer, walk around the whole exterior and take note of its condition. This helps you decide what pressure to use, what repairs are needed and which areas need extra attention.

What to Look For

  • Peeling, flaking or bubbling paint: These areas will need scraping and sanding after washing.
  • Mould and mildew: Typically black, green or grey patches, especially on south-facing walls, under eaves and around downpipes.
  • Cracks and gaps: Check render, weatherboards, window frames and joins for damage that may allow water to enter the wall.
  • Rust stains: Common on metal fixtures, roof edges and fasteners, particularly near the coast.
  • Termite activity or rot: Soft or damaged timber should be assessed by a professional before washing, as high pressure can worsen damage.
  • Loose or damaged fittings: Light fixtures, power points, flyscreens and gutters should be checked and secured.

Step Two: Prepare the Surrounding Area

Good preparation protects your property, your plants and your safety. Skipping these steps is a common cause of damage and cleanup headaches.

Protect Plants and Landscaping

Tropical gardens are a feature of many Darwin homes, and they can be sensitive to runoff, especially if you use cleaning solutions. Pre-wet nearby plants with fresh water, cover delicate foliage with drop sheets and move potted plants well away from the work area. Rinse plants again after washing to dilute any residue.

Secure Windows, Doors and Electrical Points

  • Close all windows and doors tightly before you begin.
  • Cover external power points, light fittings, meter boxes and exhaust vents with waterproof tape and plastic.
  • Check that window seals and flyscreens are intact, because high-pressure water can force its way inside.
  • Move outdoor furniture, bins, vehicles, toys and decorations clear of the area.
  • Disconnect or protect air conditioning units and cover any exposed wiring.

Step Three: Choose the Right Equipment and Pressure

Different surfaces need different pressure levels. A setting that cleans concrete safely can gouge timber or strip render. As a general guide, use lower pressure and a wider spray angle on delicate surfaces, and always test a small, hidden area first.

Typical guidance for common Darwin surfaces includes:

  • Brick and concrete: Can usually handle moderate to high pressure, though old mortar joints should be treated carefully.
  • Rendered walls: Use low to moderate pressure, as render can crack or erode if hit too hard.
  • Timber cladding and fascia: Use low pressure and work with the grain to avoid splintering.
  • Colorbond and metal sheeting: Use low pressure and a wide fan tip to avoid denting or stripping the coating.
  • Fibre cement sheeting: Use gentle pressure, as the surface can be porous and easily damaged.

A 25 to 40 degree nozzle is suitable for most general cleaning. Avoid narrow zero-degree tips, which can cut into surfaces. For stubborn mould, a soft wash approach using low pressure and a suitable cleaning solution is often more effective than force alone.

Step Four: Wash Using the Correct Technique

Working methodically gives you a consistent result and prevents streaks, damage and missed spots. Follow this sequence for best results.

  1. Start at the top: Wash from the highest point, such as eaves and gutters, and work downward so dirty water doesn't run over cleaned areas.
  2. Apply a cleaning solution where needed: Use a mould and mildew treatment on affected areas and allow it to sit for the time recommended on the product label. Never let it dry on the surface.
  3. Keep the nozzle at a steady distance: Hold it around 30 to 40 centimetres from the surface, adjusting for the material.
  4. Use smooth, overlapping strokes: Sweep side to side to avoid stripes and uneven cleaning.
  5. Avoid spraying upward under laps: Water driven behind cladding or weatherboards can cause moisture problems inside the wall.
  6. Rinse thoroughly: Remove all detergent, loosened paint and debris with clean water.

Step Five: Deal With Mould, Rust and Stains

Water pressure alone often won't kill mould spores. In Darwin's https://pressurecleaningdarwin.com.au/driveway-cleaning/ humid conditions, regrowth is quick if the spores remain. Use a purpose-made mould treatment, follow the manufacturer's safety instructions and wear protective gear such as gloves, eye protection and a mask when handling chemicals.

For rust stains, a dedicated rust remover may be needed, and any active rust on metal should be sanded back, treated and primed before painting. Oil or grease stains, often found on driveways, garage walls and carports, should be treated with a degreaser, since paint will not adhere properly over them.

Step Six: Allow Proper Drying Time

This is the step many people rush. Painting over damp surfaces can trap moisture, leading to bubbling, blistering and early peeling. In the Dry Season, with low humidity and plenty of sun, most surfaces may be ready within 24 to 48 hours. During the Wet Season, drying can take considerably longer, and you may need several days of clear weather.

A moisture meter is a handy tool for checking timber and masonry. As a rule, wait until surfaces are completely dry to the touch and show no dark, damp patches, particularly in shaded areas and on the south side of the house. Check the weather forecast before you wash so you can plan a window of dry days before painting.

Step Seven: Post-Wash Repairs and Preparation

Once the surface is clean and dry, you can see exactly what needs fixing. This stage is essential for a lasting finish.

  • Scrape and sand any remaining loose or flaking paint until edges are feathered smooth.
  • Fill holes, cracks and gaps with a suitable exterior filler or flexible sealant.
  • Replace rotted or damaged timber.
  • Spot-prime bare timber, metal and repaired areas.
  • Apply a sealer or binding primer to chalky surfaces if required.
  • Lightly sand glossy surfaces so the new paint can grip.

Common Mistakes to Avoid

Even well-intentioned DIY efforts can run into problems. Keep an eye out for these frequent errors:

  • Using excessive pressure that etches timber, strips render or damages paintwork you intend to keep.
  • Skipping mould treatment and relying on water alone.
  • Washing too close to painting day without allowing adequate drying time.
  • Forgetting to protect electrical fittings and vents.
  • Washing from the bottom up, which causes streaking and re-soiling.
  • Working on ladders with a pressure washer, where the recoil can cause serious falls.

Safety and Environmental Considerations in Darwin

Safety should always come first. Wear closed-in footwear, eye protection and hearing protection, and never point a pressure washer at people or pets. Be careful around power lines and avoid using electrical equipment in wet conditions without proper safety devices such as residual current devices.

Environmental care matters too. Wash water can carry paint chips, detergent and contaminants into stormwater drains, which flow to Darwin Harbour and surrounding waterways. Where possible, direct runoff onto lawn or garden areas rather than the street, use biodegradable cleaning products and collect loose paint flakes before they wash away. Older homes may also contain lead-based paint or asbestos-containing materials, so if your property was built before the 1990s, have suspect surfaces tested and follow appropriate safe handling practices before washing or sanding.

When to Call a Professional

Some jobs are best left to experienced local contractors. Double-storey homes, steep roof lines, delicate cladding, heavy mould infestations and properties with potential hazardous materials all carry extra risks. Professionals have commercial-grade equipment, appropriate safety gear and knowledge of how Darwin's climate affects surface preparation. Hiring a qualified provider can save you time and reduce the chance of damage that would cost more to repair later.

Quick Final Checklist

Before you pick up the paintbrush, confirm that you've done the following: inspected the property, protected plants and fittings, selected the right pressure and nozzle, washed from top to bottom, treated mould and stains, rinsed thoroughly, allowed the surface to dry fully, repaired defects and primed bare areas. Ticking off each of these steps gives your new paint the best possible start and helps it stand up to the Top End's sun, storms and humidity for years to come.

With careful preparation and a little patience, your 2026 repaint can look better and last longer, protecting one of your most valuable assets against the demands of the Darwin climate.

Darwin Pressure Cleaning

(08) 8931 2278